RADIATOR & COMPONENTS. 3. 0 liter. Fm 02/04/2019. W/E-HYBRID.. 1999 Porsche

3.0 LITER. W/E-HYBRID.

Left.3.0 LITER. Right.3.0 LITER. Upper insulator. W/E-HYBRID.

Left.3.0 LITER. Right.3.0 LITER. W/E-HYBRID.

Left.3.0 LITER. Right.3.0 LITER. Upper insulator retainer clip. W/E-HYBRID.

3.0 LITER. W/E-HYBRID. A Sensor used to measure the Temperature of the battery pack, used to determine if the Cooling system is working properly. Location-Coolant Hose. Location-Engine Block. Location-Engine Coolant Hose. Location-Engine Cylinder Head. Location-Radiator Coolant Hose. Temperature Sensor for Engine Coolant. Sending Unit. Cylinder Head. Drive Motor Battery Pack. Engine. Included with: Battery, Heat exchanger, Hose & tube assembly, Radiator.

3.0 LITER. W/E-HYBRID. A circular disk covered in rubber or plastic with a hole in the center where the edge is sometimes tensioned by a spRing that prevents fluid from leaking at the Engine Coolant Temperature Sensor. A round Ring used to Seal between the EGR Valve Temperature Sensor and it's mounting surface. A round Ring used to Seal between the Radiator Hose and it's mounting surface. An o-Ring used to prevent a leak at the Drive Motor Battery Pack Coolant Hose. Engine Coolant Temperature Sensor O-Ring. Location-Coolant Hose. Location-Cylinder Head. Location-Engine. Location-Engine Block. Location-Engine Cylinder Head. Part cannot be reused/reinstalled. switch o -. Drive Motor Battery Pack Hose O -. Engine O -. Exhaust Gas Recirculation (EGR) Valve O -. Hose AND tube Assembly o -. Radiator Hose O -. Water pipe o -. Included with: Cooler Assembly, EGR Cooler, Heat exchanger, Hose & tube Assembly, Lower Hose, Lower Hose Part cannot be reused/reinstalled, Radiator, Temp Sensor, Temperature Sensor, Temperture Sensor.

3.0 LITER. Temp sensor screw. W/E-HYBRID. A Screw that is used to secure the Hood Latch Support to its mounting point. A Screw that is used to secure the Hood Release Cable to it's mounting point. A Screw that is used to secure the Intake Air Temperature Sensor to its mounting point. A Screw that is used to secure the Radiator Support Baffle to it's mounting point. A Screw that is used to secure the Radiator Support Panel to it's mounting point. A Screw that is used to secure the Radio Amplifier to it's mounting point. A Screw that is used to secure the Trunk Floor Storage Box to its mounting point. A Screw used to secure the Drive Belt Cover to its mounting surface. A Screw used to secure the Seat Lumbar Adjustment Handle to its mounting surface. A Screw used to secure the Steering Knuckle to its mounting surface. A Screw used to secure the turbo boost Sensor to its mounting surface. A threaded rod with a Drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Engine Coolant Temperature Sensor to it's mounting point. A threaded rod with a Drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Hood Release Handle to it's mounting point. A threaded rod with a Drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Hybrid Battery Compartment to it's mounting point. A threaded rod with a Drive head (such as hex, 12 point, torx, etc.) on one end used to secure the Turbocharger Boost Sensor to it's mounting point. Bolt for the brackets that hold the Radiator Hose. Bumper Cover Reinforcement Screw. Bumper Cover Support Rail Screw. Engine Air Intake Hose Bolt. Engine Air Intake Hose Screw. Engine Coolant Pipe Bolt. Engine Coolant Reservoir Bolt. Mounting Bolt. Secures the active suspension control module to it's mounting point in the vehicle. Included with: Lower Hose, Lower Hose Part cannot be reused/reinstalled, Radiator, Reservoir cap.

Left.3.0 LITER. Lower insulator. Right.3.0 LITER. W/E-HYBRID.

Left.3.0 LITER. Lower insulator buffer. Right.3.0 LITER. W/E-HYBRID. A rubber ring with a hole in the center which provides protection through which Radiator related components pass through. Primary. Radiator Insulator. Auxiliary mount. Bracket. Bushing. Frame isolator. Grommet. Heater core. RUBBER Buffer. Support.

Left.3.0 LITER. Lower insulator mount bolt. Right.3.0 LITER. W/E-HYBRID.

3.0 LITER. Drain plug. W/E-HYBRID.

3.0 LITER. Reservoir. W/E-HYBRID.

3.0 LITER. fm 02/04/2019. Lower bracket. W/E-HYBRID.

3.0 LITER. Lower bracket bolt. W/E-HYBRID. A Bolt used to attach the Drive Motor Battery Pack Control Module to its mounting point. A threaded rod with a Drive head (such as hex, 12 point, torx, etc) on one end used to secure the HVAC Electronic Control Module to it's mounting point. A threaded rod with a Drive head (such as hex, 12 point, torx, etc) on one end used to secure the Supercharger Intercooler to it's mounting point. Air Filter Housing Bolt. Battery Tray Bolt. Bumper Guide Bolt. Engine Coolant Reservoir Bolt. Engine Water Pump Bolt. Air Filter Housing. Battery Tray. Bumper Guide. Charge Air Cooler. Cover retainer screw. Drive Motor Battery Pack Control Module. Engine Coolant Reservoir. Engine Water Pump. HEXAGON - HEAD SCREW 6. HVAC Control Module. Intercooler. Mount bracket. Included with: Cover.

3.0 LITER. Lower bracket grommet. W/E-HYBRID.

3.0 LITER. Lower bracket nut. W/E-HYBRID. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Door Shell. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the Engine Coolant Expansion Tank. A solid metal or plastic block with a threaded hole in the center which is used to tighten or adjust the HVAC Case. Bracket. Door Shell cap. Engine Coolant Reservoir. HVAC Unit Case. Rail REINFORCED. Rivetted cap.

3.0 LITER. W/E-HYBRID.

3.0 LITER. Seal. W/E-HYBRID.

3.0 LITER. W/E-HYBRID.